DuraSeal DuraClear Sealer is a waterborne, fast-drying, non-ambering, crystal-clear sealer specially formulated to provide an outstanding base coat for DuraSeal water-based finishes. DuraSeal DuraClear Sealer helps prevent tannin discoloration.
- Non-Ambering
- Low Odor
- Easy Water Clean-Up
- Ultra Fast-Drying
Description
SURFACE PREPARATION
NATURAL FLOORS: Sand and prepare floor according to NWFA recommended methods. Finish abrading with 120 or 150 grit pad or equivalent. Do not use steel wool. Vacuum very thoroughly; then tack with a towel or mop lightly dampened with water to remove all dust. Apply DuraSeal® DuraClear™ Sealer as described below and allow to dry 1-2 hours; then apply coats of your selected DuraSeal® waterborne finish per label directions. Do not screen or abrade sealer prior to applying finish.
STAINED FLOORS: Sand and prepare floor according to NWFA recommended methods. Finish abrading with 100 grit grit pad or equivalent. Do not use steel wool. Apply DuraSeal® Penetrating Finish or DuraSeal® Quick Coat according to directions. Make sure stain is thoroughly cured before topcoating. NOTE: If DuraSeal® Penetrating Finish or DuraSeal® Quick Coat is used, buff cured stain with a green pad. Tack with water-dampened cloth for best leveling and adhesion. Apply DuraSeal® DuraClear™ Sealer as described below and allow to dry 1-2 hours; then apply your selected DuraSeal® waterborne finish per label directions. Do not screen or abrade sealer prior to applying finish.
APPLICATION
- Pour a 4 – 6″ wide line of DuraSeal® DuraClear™ Sealer directly from the container along the starting wall. Go with the direction of the floor or grain.
- Pull the sealer with a clean, moistened applicator toward the other wall with an angled, squeegee motion.
- As you approach the wall, turn applicator and pad out excess material parallel to the wet edge.
- Feather all turns, stopping and starting points.
- Allow sealer to dry 1-2 hours; then apply finish within 24 hours. Dry time is based on conditions of 77° F and 50% relative humidity at the recommended application rate.
NOTE: Use two coats of DuraSeal® DuraClear™ Sealer on natural white oak floors.
DRY TIME
Light foot traffic is acceptable after 24 hours. Do not expose the finish to rugs, cleaners, spills or heavy traffic for one week. Dry times are based on conditions of 77°F and 50% relative humidity at the recommended application rates.
CLEAN-UP
Clean application tools with warm water immediately after use.
COVERAGE
Clean application tools with warm water immediately after use.
STORAGE
Store at room temperature. If stored at high temperature, cool to room temperature before use. Keep from freezing. If frozen, warm to room temperature and mix thoroughly before use. Maximum VOC: 100g/l or 0.83 lbs/gal. Do not thin.
FIRST AID
In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
AVAILABLE IN
| TYPE | SIZE | PROD. NO. | QTY | PDS | GHS SDS |
|---|---|---|---|---|---|
| GAL | 800110000 | 4 | PDS | SDS |
PHYSICAL PROPERTIES
| Testing Method | ||||
|---|---|---|---|---|
| Resin type | Urethane | |||
| Solvent | Water, 2-Methoxymethylethoxypropanol | |||
| Odor | Mild Amine | |||
| No. of coats | 1 – 2 | |||
| Dry-time |
|
ASTM D 1640 & | ||
| Dry film thickness | 0.6 mil/coat | |||
| Flash point | >212°F (SETAFLASH*) | SETAFLASH* | ||
| ASTM D 3828 | ||||
| Applicator | Natural bristle or foam brush, lambswool or synthetic pad | |||
| VOC (grams/liter) | 100 maximum | ASTM D 3960 | ||
| Coverage (sq. ft/gal) | Approx. 500-600 | |||
| % Solids | 36.1 – 38.1 | ASTM D 2369 | ||
| Pounds/gallon | 8.34 – 8.74 | |||
| pH | 5.5 – 6.5 | |||
| Viscosity (centipoises) | 45 – 65 |
*SETAFLASH is a registered trademark of Stanhope-Seta Limited.
